Kranzle Stationary HOT Floor Mounted  pressure washers are from Dual Pumps and Supplied by;- Malcolm  Smith Power Cleaning - Malcleanse on-line shopping

Click on Photo or Name to take you to my on-line shop - Malcleanse.co.uk - Malcolm Smith Power Cleaning

10 Lpm at 160 Bar Kranzle Floor Mounted Hot Pressure Washer 24 kw K601EST24

10 Lpm at 160 Bar Kranzle Floor Mounted Hot Pressure Washer 24 kw K601EST24 KRANZLE

Part No: K601EST24

Volts: 415

Lpm: 10

Bar: 160

Power: 24 kw

10 Lpm at 260 Bar 24 kw Floor Mounted Hot Pressure Washer Three Phase from Kranzle. Post pump heating gives clear advantages over conventional 'kettle' type hot water pressure washers. Good design & rugged construction.

• Operating pressure 100 / 160 bar (~2300 psi adjustable) Nozzle size 25045 / 2503 Water flow 10 Ltrs/Min. @ 1400 rpm Max. hot water output 80c High pressure detergent facility Automatic stop start. Water flow detection safety system. Anti superheating safety thermostats fitted as standard. Stainless steel cabinet Optional non marking hygiene hose. Supply 415v 3ph 50 Hz 24kw heating power Dimensions 790 x 590 x 980 mm (without reel) No pre heating time required.

Continuous hot water output. Water is heated after the pump. These machine are built to the highest standards. Post pump heating gives three clear advantages over conventional 'kettle' type hot water pressure washers. These Therms have low maintenance needs and are very cost effective. Good design and rugged construction makes this probably the most reliable electrically heated cleaner on the market By using special high pressure heating coils you do away with the need to switch the machine on 15 minutes before you want to use it as the water is heated as it passes though the pressure washer. These special high pressure heating coils are after the high pressure pump so the pump seals, O rings and valves are not affected by the hot water.

The other advantage with this system is that you have hot water at a constant temperature because the hot water is not being cooled down by cold water entering a tank. On the 600/601 models the pump produces up to 2400 psi (160 Bar) with a maximum water flow of 10 Ltrs/min. 24kw will heat the incoming water by a constant 35 degrees centigrade at maximum flow and pressure 36kw will raise the water temp by a constant 50 degrees, assuming inlet water temperature is 10 deg that would give you 60 degrees output at maximum flow/pressure (Pressure and flow can be reduced on all models to increase the output temperature) On the 900 model you can have 15 Ltr/min at approx 3000 psi (200 Bar) or the machine can be set to 10 Ltr/min 48kw will raise 15 Ltr/min by a constant 46 degrees at maximum pressure and flow 48kw will raise 10 Ltr/Min by a constant 70 degrees, so a cold water supply at an ambient temperature of 10 degrees would be heated to the maximum of 80 degrees. The maximum output temperature on all models is set to 80 degrees for safety reasons. Electrically heated Therms are easy to use, versatile and have long life expectancy. Every effort has been made to make a machine that is the best on the market and yet still be affordable.

10 Lpm at 160 Bar Kranzle Floor Mounted Hot Pressure Washer 36 kw K601EST36

10 Lpm at 160 Bar Kranzle Floor Mounted Hot Pressure Washer 36 kw K601EST36 KRANZLE

Part No: K601EST36

Volts: 415

Lpm: 10

Bar: 160

Power: 36 kw

10 Lpm at 260 Bar 36kw Floor Mounted Hot Pressure Washer Three Phase from Kranzle. Post pump heating gives clear advantages over conventional 'kettle' type hot water pressure washers. Good design & rugged construction

• Operating pressure 100 / 160 bar (~2300 psi adjustable) Nozzle size 25045 / 2503 Water flow 10 Ltrs/Min. @ 1400 rpm Max. hot water output 80c High pressure detergent facility Automatic stop start. Water flow detection safety system. Anti superheating safety thermostats fitted as standard. Stainless steel cabinet Optional non marking hygiene hose. Supply 415v 3ph 50 Hz 36kw heating power Dimensions 790 x 590 x 980 mm (without reel) No pre heating time required. Continuous hot water output. Water is heated after the pump. These machine are built to the highest standards. Post pump heating gives three clear advantages over conventional 'kettle' type hot water pressure washers.

These Therms have low maintenance needs and are very cost effective. Good design and rugged construction makes this probably the most reliable electrically heated cleaner on the market By using special high pressure heating coils you do away with the need to switch the machine on 15 minutes before you want to use it as the water is heated as it passes though the pressure washer. These special high pressure heating coils are after the high pressure pump so the pump seals, O rings and valves are not affected by the hot water. The other advantage with this system is that you have hot water at a constant temperature because the hot water is not being cooled down by cold water entering a tank.

On the 600/601 models the pump produces up to 2400 psi (160 Bar) with a maximum water flow of 10 Ltrs/min. 24kw will heat the incoming water by a constant 35 degrees centigrade at maximum flow and pressure 36kw will raise the water temp by a constant 50 degrees, assuming inlet water temperature is 10 deg that would give you 60 degrees output at maximum flow/pressure (Pressure and flow can be reduced on all models to increase the output temperature)

On the 900 model you can have 15 Ltr/min at approx 3000 psi (200 Bar) or the machine can be set to 10 Ltr/min 48kw will raise 15 Ltr/min by a constant 46 degrees at maximum pressure and flow 48kw will raise 10 Ltr/Min by a constant 70 degrees, so a cold water supply at an ambient temperature of 10 degrees would be heated to the maximum of 80 degrees. The maximum output temperature on all models is set to 80 degrees for safety reasons. Electrically heated Therms are easy to use, versatile and have long life expectancy. Every effort has been made to make a machine that is the best on the market and yet still be affordable.

15 Lpm at 200 Bar Kranzle Floor Mounted Hot Pressure Washer 48 kw K900EST48

15 Lpm at 200 Bar Kranzle Floor Mounted Hot Pressure Washer 48 kw K900EST48 KRANZLE

Part No: K900EST48

Volts: 415

Lpm: 15

Bar: 200

Power: 48 kw

10 Lpm at 260 48 kw Bar Floor Mounted Hot Pressure Washer Three Phase from Kranzle. Post pump heating gives clear advantages over conventional \\\'kettle\\\' type hot water pressure washers. Good design & rugged construction

• Max operating pressure 200 bar (~3300 psi adjustable) Nozzle size 25055 Water flow up to 15 Ltrs/Min. Max. hot water output 80c High pressure detergent facility Automatic stop start. Water flow detection safety system. Anti superheating safety thermostats fitted as standard. Stainless steel cabinet Optional non marking hygiene hose. Supply 415v 3ph 50 Hz 48kw heating power Dimensions 790 x 590 x 980 mm (without reel) No pre heating time required. Continuous hot water output.

Water is heated after the pump. These machine are built to the highest standards. Post pump heating gives three clear advantages over conventional \\\'kettle\\\' type hot water pressure washers. These Therms have low maintenance needs and are very cost effective. Good design and rugged construction makes this probably the most reliable electrically heated cleaner on the market By using special high pressure heating coils you do away with the need to switch the machine on 15 minutes before you want to use it as the water is heated as it passes though the pressure washer.

These special high pressure heating coils are after the high pressure pump so the pump seals, O rings and valves are not affected by the hot water. The other advantage with this system is that you have hot water at a constant temperature because the hot water is not being cooled down by cold water entering a tank. On the 600/601 models the pump produces up to 2400 psi (160 Bar) with a maximum water flow of 10 Ltrs/min. 24kw will heat the incoming water by a constant 35 degrees centigrade at maximum flow and pressure 36kw will raise the water temp by a constant 50 degrees, assuming inlet water temperature is 10 deg that would give you 60 degrees output at maximum flow/pressure (Pressure and flow can be reduced on all models to increase the output temperature) On the 900 model you can have 15 Ltr/min at approx 3000 psi (200 Bar) or the machine can be set to 10 Ltr/min 48kw will raise 15 Ltr/min by a constant 46 degrees at maximum pressure and flow 48kw will raise 10 Ltr/Min by a constant 70 degrees, so a cold water supply at an ambient temperature of 10 degrees would be heated to the maximum of 80 degrees.

The maximum output temperature on all models is set to 80 degrees for safety reasons. Electrically heated Therms are easy to use, versatile and have long life expectancy. Every effort has been made to make a machine that is the best on the market and yet still be affordable.

Click here to go to my online shop  - STATIONAY HOT  PRESSURE WASHERS